Application: The anaerobic thread locking to avoid loosening & leakage of threaded fasteners. For M6-M36 thread locking & sealing. Prevent thread corrosion. Typical uses: screw locking. Specification: Base chemical composition: methyl methacrylate Appearance: Red viscous liquid Viscosity (m Pa.s): 1000-3000 Specific Gravity: 1.05 Flash point (C):108 Maximum fill the gap (mm): 0.13 Room temperature curing time (min):20 After curing properties: Full cure time at room temperature (hr): 24 Destruction of torque (Nm): 3-12 The average removal torque (Nm): 2-10 Operating Temperature (C): -54 ~ 149 Instructions for use:painted surfaces should be clean, dry & no oil.bolts painted in sufficient quantity to fill all engaged threads, a thin layer of the product results in a 0.05 mm or less work best. For large thread sizes, the larger the gap will affect cure speed & strength of the product. This product will reduce the friction force (torque tension ratio) assembly generated. Need to be fastened to the threaded applications critical value, the need to determine in advance a good ratio. Caution: The anaerobic thread locking should not be used on plastic parts; in order to avoid contamination of the original glue, do not have poured the glue back to the original packaging. Safety Precautions: The anaerobic thread locking containing methyl acrylate, skin & eye irritation. If skin contact, immediately wash with water; If contact with eyes, rinse immediately with water & go to the hospital for tr ...

Product Introduction:K-0271 is a single component, medium viscosity, high strength anaerobic thread locking sealant. This product is used between close fitting metal surfaces & cured & air separation. Available Hand Tools Demolition Applications: Avoid loosening & leakage of threaded fasteners. M36 thread fasteners for permanent locking & sealing, to prevent thread corrosion. Typical uses: Studs screwed into the end locking (such as cylinder head studs) Specification: Base material chemical composition: methacrylate Appearance: red thick liquid Viscosity (m Pa) s): 300 ~ 800 Specific gravity: 1.05 Flash point:108 The biggest fill gaps (mm): 0.13 At room temperature curing time (min): 20 or less After curing performance: All solid at room temperature time (hr): 24 Failure moment (N, m): 20 Average removal torque (N, m): 20 Working temperature: 54-149 Instruction manual:1. The coated surface should be clean, dry & free of grease.2. Insert the bolt painted in sufficient quantity to fill all engaged threads, a thin layer of this product work results in a 0.05 mm or less optimal.3. For large thread sizes, larger gap will affect cure speed & strength of the product. This product will reduce the friction force (torque tension ratio) assembly generated. The need to screw fastening applications to the critical value, the need to determine in advance the good of this ratio. Caution: This product should not be used on plastics; in order to avoid contamination of the original glue, do not ...

Application: The anaerobic thread locking to avoid loosening & leakage of threaded fasteners. For M6-M36 thread locking & sealing. Prevent thread corrosion. Typical uses: screw locking. Specification: Base chemical composition: methyl methacrylate Appearance: Red viscous liquid Viscosity (m Pa.s): 8000-15000 Specific Gravity: 1.12 Flash point (C): 93 Maximum fill the gap (mm): 0.25 Room temperature curing time (min):15 After curing properties: Full cure time at room temperature (hr): 24 Destruction of torque (Nm): 25 The average removal torque (Nm): 20 Operating Temperature (C): -54 ~ 203 Instructions for use:painted surfaces should be clean, dry & no oil.bolts painted in sufficient quantity to fill all engaged threads, a thin layer of the product results in a 0.05 mm or less work best. For large thread sizes, the larger the gap will affect cure speed & strength of the product. This product will reduce the friction force (torque tension ratio) assembly generated. Need to be fastened to the threaded applications critical value, the need to determine in advance a good ratio. Caution: The anaerobic thread locking should not be used on plastic parts; in order to avoid contamination of the original glue, do not have poured the glue back to the original packaging. Safety Precautions: The anaerobic thread locking containing methyl acrylate, skin & eye irritation. If skin contact, immediately wash with water; If contact with eyes, rinse immediately with water & go to the hospital for treat ...

Product Introduction:K-0340 is a single component, medium viscosity, high strength anaerobic thread locking sealant. This product is used between close fitting metal surfaces & cured & air separation. Available Hand Tools Demolition Applications: Avoid loosening & leakage of threaded fasteners. M36 thread fasteners for permanent locking & sealing, to prevent thread corrosion. Typical uses: Studs screwed into the end locking (such as cylinder head studs) Specification: Base material chemical composition: methacrylate Appearance: Yellow thick liquid Viscosity (m Pa) s): 300 ~ 600 Specific gravity: 1.05 Flash point:108 The biggest fill gaps (mm): 0.13 At room temperature curing time (min): 15 After curing performance: All solid at room temperature time (hr): 24 Failure moment (N, m): 10 Average removal torque (N, m): 15 Working temperature: 54-149 Instruction manual:1. The coated surface should be clean, dry & free of grease.2. Insert the bolt painted in sufficient quantity to fill all engaged threads, a thin layer of this product work results in a 0.05 mm or less optimal.3. For large thread sizes, larger gap will affect cure speed & strength of the product. This product will reduce the friction force (torque tension ratio) assembly generated. The need to screw fastening applications to the critical value, the need to determine in advance the good of this ratio. Caution: This product should not be used on plastics; in order to avoid contamination of the original glue, do not have ...

Use: Mainly used in electrical & electronic products, fixing screws, locking & identification purposes. Instructions: Component surfaces do general cleaning, adhesive bonding, can be cured at room temperature. Feature:1. shred of good, easy to operate, suitable for pipeline operation;2. The film toughness, impact resistance, shock;3. permeability good;4. Low torque, easy to loose screws out. Specification:1. Appearance: Yellow viscous liquid, no mechanical impurities 2. Solid content: 605%3. Temperature (C): 105 Usage: Available oiler Caution: This product contains flammable solvents, use & storage away from fire, maintain good ventilation in the workplace. Packging Included:1X Kafuter 75g K-1668 ...

Description: Brand:KAIDIWEIItem NO.:663003 Item Name: Double-Room Car
Material: Alloy, ABS
Colour: Orange,

...

Description: Brand:KAIDIWEIItem NO.:685003 Item Name: Military Helicopter
Material: Alloy, ABSWeight: About 1000g Package


...

Description: Brand:KAIDIWEIItem NO.:685056 Item Name: Antiaircraft Artillery Style: Alloy Military Series
Material: Alloy,
...

Description: Brand:KAIDIWEIItem NO.:685052 Item Name: Military Helicopter Model (Alloy)
Material: Alloy, ABSWeight: About
...

Description: Brand:KAIDIWEIItem NO.:685004 Item Name: Humvee Battlefield Vehicle Style: Military Off-Road Vehicle
Material:
...