Specification: Weight: 215g
Size: 10.7*4.2*7.5cm OE number: 1354050030 13540-50030 Package Included:1 X Timing Tensioner
...

Main
Features:● Easy to use Control Center● Nonstick Grill & Toaster●4-cup Capacity Glass Coffee● Swing-Out Filter Compartment
...

Description :A perfect gift for your pet. Helps keep your pet active & healthy. Specification: Type: Pet Toys
Material:
...

TINSLY 2307 2650KV 4-5S Brushless Motor 35g for RC FPV Racing Drone Description: Brand name: TINSLYItem name: TSL-2307 Configuration: 12N14 P Stator diamter: 23mm Stator length: 7mm Shaft diameter: 4mm (Hollow) Motor (dimension (Dia.* Len)): 26.7*30.5mm Rotor: N52H arc magnets Bearings: NSKBase casing: Al 7075 Wire AWG: 20AWGWeight (g): 35KV: 2650kv Idle current (10)@10V (A): 2.8 No.of Cells (Lipo): 4~5 S Max continuous (power (W)15S): 1000 Internal resistance: 29m Max current (30S): 48 A Max.effciency current: (4-8A)81%
Features:1. NSK high-efficiency bearings 2. 0.15mm silicon steel laminations 3. N52H arc magnets 4. Al 7075 CNC5. The weight is 34g only Package included:1 x TSL2307 motor 1 x M5 aluminum lock nut 4 x M3x 6 screws 4 x M3x 8 screws
...

Tinsly S50 Big Shark 215mm 5 Inch FPV Racing Frame 4mm Arm Thickness Notes: the S50 Big Shark frame kit doesnt come with the PDB. Description: Brand: Tinsly Item name: S50 Big Shark Wheelbase: 215mm
Material: 3K carbon fiber + aviation aluminum 7075 Weight: 90g Arms board thickness: 4mm Side board thickness: 1.5mm Props

Size: 5inch Package included:1x S50 Big Shark frame kit 1x XT60 connector 2x battery strap


...

TINSLY-H60 265mm Wheelbase 6 Inch Carbon Fiber Frame Kit 4mm Arm for RC Drone FPV Racing Notes:this item only comes with frame kit, not including otherelectronic equipment. Specification: Item name:TINSLY-H60 Wheelbase: 265mm
Material: carbon fiber Weight: 116g Arm thickness: 4mm Recommended propeller: 6 inch Package included:1x TINSLY-H60 frame kit
...

TINSLY-X60 248mm Wheelbase 6 Inch Carbon Fiber Frame Kit 4mm Arm for RC Drone FPV Racing Notes:this item only comes with frame kit, not including any eletronic equipment. Specification: Item name:TINSLY-X60 frame kit Wheelbase: 248mm
Material: carbon fiber Weight: 83g Arm thickness: 4mm Recommended propeller: 6 inch Package included:1x TINSLY-X60 frame kit
...

Tinting Perforated Mesh Film Fly Eye MOT Legal Tint Headlight Rear Lamp 40x 106cm Specifications:
Size: Approx. 40 x 106cm
...

Tinting Perforated Mesh Film Sticker 60x 106cm for Tint Headlight Rear Lamp

Features:-Water Resistant-UV Stable-Suitable

...

Tiny 2.4G 6CH Receiver Compatible with DSM2 PPM Signal Output for Eachine QX80 QX90 QX95 Description: Item Name: Tiny DSM2 Receiver Channels: PWM 5CH, PPM 6CHReceiving Sensitivity: -99d Bm Frequency Range: 2.4-2.48 G Hz Power: 3.7-5V DCAntenna Length: 30mm
Size: 9.5mm*10.5mm*2.5mm Weight: 0.28g
Colour: Blue / Red (Send Randomly)
Features: This DSM2 could support all JR & Spektrum transmitter. It also could support WALKERA DEVO 10 & DEVO 7E with deviation firmware. Support all transmitter which has DSM2 protocol. Binding: There is no bind pin designed, the receiver has an autobind procedure just like with small quad-copters. When switch on, receiver tries to bind with transmitter for about 3s (led is blinking). If receiver find a transmitter (must be also in bind mode) then it records transmitter identifier & works with it. If it cant bind with a transmitter then is retrieves previously bind transmitter identifier & works with it. This way, you save an extra pin & just need to bindonly once. After bind procedure, If reception is ok then led on, if no reception at all led off, if reception bad led is blinking randomly. Note:CH1 to CH5 is servo signal output. If CH1 connect to GND, CH2 will output 6CH PPM signal. Package Included:1 x Tiny DSM2 Receiver


...