About Us
Contact Us
Privacy Policy
Cookie Usage
Add Your Store

More From Contributor

Holybro Kakute F7 Flight Controller Betaflight OSD+Atlatl HV V2 5.8G FPV Transmitter for RC Drone
Holybro Kakute F7
Flight Controller
Betaflight OSD+ Atlatl
HV V2 5.8G
FPV Transmitter For RC
Drone
£73.93
Holybro Kakute F7 Flight Controller Betaflight OSD+ Atlatl HV V2 5.8G FPV Transmitter for RC Drone Specification: Holybro Kakute F7: Brand name: Holybro Item name: Kakute F7MCU: STM32F745 32-bit processor IMU: ICM20689 (SPI) Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART) 6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work on any UART without uninvert hack. Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only. PPM & PWM receivers are not supported.TF card for Blackbox logging Dimensions: 35x 41x 7mm (
Includes: foam-mounted gyro board in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 9g
Features: Supports Betaflight, Butterflight, & Cleanflight. Betaflight OSD. Change PIDs, adjust common configuration parameters, & change video transmitter channel & power level, all using your transmitter sticks & goggles. Soft-mounting built in. The IMU (gyro) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself. High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro & accelerometer. Can run at up to 32 k Hz sampling rate. Ready for autonomous flight: Integrated BMP280 barometer & SCL/SDA pads for use with external GPS/magnetometer units. 2 oz. copper PCB allows up to 120A maximum continuous current. Dedicated bootloader button for easy firmware fla

...
Available
Holybro Kakute F7 HDV AIO & 4* Tekko32 F3 Metal 65A ESC For DJI Air Unit FPV Racing RC Drone
Holybro Kakute F7 HDV
AIO & 4* Tekko 32 F3
Metal 65A ESC For DJI
Air Unit FPV Racing
RC Drone
£137.32
Description: Brand: Holybro Item Name: Holybro Kakute F7 HDV AIO4* Tekko 32 F3 Metal 65A ESCHolybro Kakute F7 HDV AIOSpecification: Overview Holybro Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module. The GH portavailable on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV AIOto the DJI FPV VTx, for both signal & power supply.
Features: Supports Betaflight. High-performance / low-noise IMU. MPU6000 with 6-axis gyro & accelerometer. Ready for autonomous flight: Integrated BMP280 barometer & SCL/SDA for use with external GPS/magnetometer units. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. 2 oz. copper PCB allows up to 120A maximum continuous current. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on B+ padonly). Automatic voltage monitoring. No need to run a separate v Bat wire for voltage monitoring; the KAKUTE F7 HDV AIO monitors voltage directly from the power supply. Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V & 8V. 5 Voutput up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output upto 2A to DJI FPV VTx. Supports BLHeli pass-through for easy ESC upgrade & configuration. Specifications: MCU: STM32F745 32-bit processor IMU:MPU6000 Barometer: BMP280 USB (Universal Serial Bus) VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART) 6 hardware UARTS (UART1, 2, 3, 4
...
Available
Holybro Kakute F7 HDV AIO & 4*Tekko32 F3 35A ESC For DJI Air Unit For FPV Racing RC Drone
Holybro Kakute F7 HDV
AIO & 4* Tekko 32 F3 35A
ESC For DJI Air Unit
For FPV Racing
RC Drone
£112.54
Holybro Kakute F7 HDV AIOOverview Holybro Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module. The GH portavailable on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV AIOto the DJI FPV VTx, for both signal & power supply.
Features: Supports Betaflight. High-performance / low-noise IMU. MPU6000 with 6-axis gyro & accelerometer. Ready for autonomous flight: Integrated BMP280 barometer & SCL/SDA for use with external GPS/magnetometer units. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. 2 oz. copper PCB allows up to 120A maximum continuous current. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on B+ padonly). Automatic voltage monitoring. No need to run a separate v Bat wire for voltage monitoring; the KAKUTE F7 HDV AIO monitors voltage directly from the power supply. Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V & 8V. 5 Voutput up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output upto 2A to DJI FPV VTx. Supports BLHeli pass-through for easy ESC upgrade & configuration. Specifications: MCU: STM32F745 32-bit processor IMU:MPU6000 Barometer: BMP280 USB (Universal Serial Bus) VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART) 6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work onany UAR
...
Available
HolyBro Kakute F7 HDV AIO 30.5mm For DJI Air Unit FPV Racing Multi Rotor Parts
Holy Bro Kakute F7 HDV
AIO 30.5mm For DJI Air
Unit FPV Racing Multi
Rotor Parts
£45.00
Overview Holybro Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module. The GH portavailable on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV AIOto the DJI FPV VTx, for both signal & power supply. Features Supports Betaflight. High-performance / low-noise IMU. MPU6000 with 6-axis gyro & accelerometer. Ready for autonomous flight: Integrated BMP280 barometer & SCL/SDA for use with external GPS/magnetometer units. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. 2 oz. copper PCB allows up to 120A maximum continuous current. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on B+ padonly). Automatic voltage monitoring. No need to run a separate v Bat wire for voltage monitoring; the KAKUTE F7 HDV AIO monitors voltage directly from the power supply. Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V & 8V. 5 Voutput up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output upto 2A to DJI FPV VTx. Supports BLHeli pass-through for easy ESC upgrade & configuration. Specifications MCU: STM32F745 32-bit processor IMU:MPU6000 Barometer: BMP280 USB (Universal Serial Bus) VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART) 6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work onany UART without uninvert hack. Su ...
Available
Holybro Kakute F7 HDV Flight Controller STM32F745 with Barometer compatible for DJI FPV 30.5x30.5mm 8g
Holybro Kakute F7 HDV
Flight Controller
STM32F745
With Barometer
Compatible For DJI FPV
30.5x 30.5mm 8g
£37.99
Overview Holy Bro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holy Bro Kakute F7 HDV to the DJI FPV VTx, for both signal & power. Specifications:MCU: STM32F745 32-bit processor IMU:PMU6000 Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART)6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work on any UART without uninvert hack. Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only. PPM & PWM receivers are not supported.TF card for Blackbox logging Dimensions: 35x 35mm Mounting Holes: Standard 30.5mm square to center of holes Weight: 8g
Features: Supports Betaflight, Butterflight, & Cleanflight. High-performance / low-noise IMU. MPU6000 with 6-axis gyro & accelerometer. Ready for autonomous flight: Integrated BMP280 barometer & SCL/SDA for use with external GPS/magnetometer units. Dedicated bootloader button for easy firmware flashing. Low-profile design fits into even very compact frames. Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on B+ pad only). Automatic voltage monitoring. No need to run a separate v Bat wire for voltage monitoring; the KAKUTE F7 HDV monitors voltage directly from the power supply. Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V & 8V. 5V output up to 1.5A to po
...
Available
Holybro Kakute F7 Mini FC & Tekko32 F3 45A 4In1 Mini ESC & Atlatl HV Micro VTX FPV Combo Stack Flytower For FPV Racing R
Holybro Kakute F7 Mini
FC & Tekko 32 F3 45A
4 In 1 Mini ESC & Atlatl
HV Micro VTX FPV
Combo Stack Flytower
For FPV Racing R
£93.73
Description: Brand: Holybro Item Name: Holybro Kakute F7 Mini FCTekko 32 F3 45A 4 In 1 Mini ESCAtlatl HV Micro VTX FPV Combo Holybro Kakute F7 mini Specification:MCU: STM32F745VGH6 32-bit processor, 216 M Hz, 320 Kbytes RAM, 1 Mbytes Flash Baro: Yes IMU: ICM20689 (SPI) Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART)5.5 hardware UARTS (UART1, 2, 3, 4, 6, 7) Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only. PPM & PWM receivers are not supported. Onbord 16 Mbytes for Blackbox logging 5V Power Out: 1.0A max 3.3V Power Out: 0.2A max Dimensions: 33x 26x 6mm Mounting Holes: Standard 20mm square to center of holes Weight: 4g Tekko 32 F3 45A 4 In 1 Mini ESC Specification: Con. Current: 45 A Peak Current: 50AF3MCU, runsdoublefasterthan F05132bit ESCwith BLHELI32firmware Supports 3-6 Slipoinput PWMinput, TLMsupported Voltageoutput (VBAT)NOBECSupportsoneshot/ Multishot/ Dshot PWMSupportsdampedlight Ext. cap needed for 6s (470uf 35v for 6s usage.) Mountingholes M2, 20x 20mm
Size:30 x 36 mm Weight: 7.8g Atlatl HV Micro VTX Specification: Brand Name: Holybro Model: Atlatl HV micro V1.0 Item Name:5.8G 40CH 25/200/500/800m W Switchable FPV Transmitter Output Power: 0.5 m W (pit mode), 25 m W, 200 m W, 500 m W, 800 m W Audio: 6.5 MHz Mono Antenna Connector: MMCXInput Voltage: 7 to 21 volts (2-4S Li Po) with absolute maximum 30 volts Dimensions: 30x 26x 7mm Mounting Holes: Standard 20mm square to center of holes Weight: 3.6g

Features:- Compatible with all major FPV receivers from vendors such as Fatshark,


...
Available
Holybro Kakute F7 Mini Flight Controller & Tekko32 F3 45A Mini 4in1 ESC & 40CH 25/100mW VTX for RC Drone
Holybro Kakute F7 Mini
Flight Controller &
Tekko 32 F3 45A Mini
4in 1 ESC & 40CH
25/100m W VTX For RC
Drone
£116.51
Holybro Kakute F7 Mini Flight Controller Tekko 32 F3 45A Mini 4in 1 ESC40CH 25/100m W VTXSpecication: Brand Name: Holybro Model:KAKUTE F7 Mini Item Name: F7 2-6S Flight Controller Tekko 32 F3 45A Mini BL_32 4in 1 ESC Combo KAKUTE F7 Mini Flight Controller MCU: STM32F745VGH6 32-bit processor, 216 M Hz, 320 Kbytes RAM, 1 Mbytes Flash IMU: ICM20689 (SPI) Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART)5.5 hardware UARTS (UART1, 2, 3, 4, 6, 7) Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only.PPM & PWM receivers are not supported. Onbord 16 Mbytes for Blackbox logging 5V Power Out: 1.0A max 3.3V Power Out: 0.2A max Dimensions: 33x 26x 6mm Mounting Holes: Standard 20mm square to center of holes Weight: 4g Tekko 32 F3 45A Mini ESCItem Name: 45A BLheli_32 3-6S 4 in 1 ESCCon. Current: 45 A Peak Current: 50A- F3 MCU, runs double faster than F051- 32bit ESC with BLHELI32 firmware- Supports 3-6S lipo input-PWM input, TLM supported- Voltage output (VBAT)- NO BEC- Supports oneshot / Multishot / Dshot PWM- Supports damped light- Ext. cap needed for 6s (470uf 35v for 6s usage.)- Mounting holes M2, 20x 20mm-
Size:30 x 36 mm- Weight: 7.8g Atlatl Mini FPV Video Transmitter (Manual) Output Power: 0.5 m W (pit mode), 25 m W, 100 m W Antenna Connector: MMCXInput Voltage: 4.5 to 5.5 volts (nominal 5v power) Dimensions: 19x 16x 4.5mm Weight: 1.6g (without antenna) Packag Included:1x F7 Flight Controller Board 1x Tekko 32 F3 4in 1 45A mini ESC1x 40CH FPV Transmitter 1x M2 Rubber rings 1
...
Available
Holybro Kakute F7 V1.5 Flight Controller & 65A BL_32 Tekko32F3 Metal 4in1 ESC 4-6S Stack Combo for RC Drone
Holybro Kakute F7 V1.5
Flight Controller &
65A BL_32 Tekko 32F3
Metal 4in 1 ESC
4-6S Stack Combo For
RC Drone
£133.53
Holybro Kakute F7 V1.5 Flight Controller 65A BL_32 Tekko 32F3 Metal 4in 1 ESC 4-6S Stack Combo for RC Drone Specification: Brand Name: Holybro Item Name: F7 Flight Controller 65A 4 in 1 ESC Stack Kakute F7 V1.5 Flight Controller (Manual ) Brand name: Holybro Item name: Kakute F7 V1.5MCU: STM32F745 32-bit processor IMU: MPU6000 (SPI) Barometer: BMP280 Current Sensor: Approx. 130 amps maximum measurable value USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART)6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work on any UART without uninvert hack. Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only. PPM & PWM receivers are not supported.TF card for Blackbox logging Dimensions: 35x 41x 7mm (
Includes: foam-mounted gyro board in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 8g Tekko 32F3 Metal 4in 1 ESC (Manual) Brand Name: Holybro Model: Tekko 32F3 Metal F3 (M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108 Mhz The 4in 1 has onboard analog current sensor, & TLM function (then no current reading over TLM) Using metal case mosfet for better Heat dissipation Supports Lipo 4-6 S Ext. cap needed for 6s (470uf 35v for 6s usage.)
Size:42 x 42 mm Mounting holes:30.530.5mm Weight: 12g Notice: The air flow is very import if you want to run this 4in 1 in high current. The input cable (from lipo to 4in 1), should be good soldered, & at least 12AWG

Features:- The 4in 1 has onboard



...
Available
Holybro Kakute F7 V1.5 Flight Controller & Atlalt HV V2 40CH VTX & 65A BL_32 Tekko32 F3 Metal 4in1 ESC Combo
Holybro Kakute F7 V1.5
Flight Controller &
Atlalt HV V2 40CH VTX
& 65A BL_32 Tekko 32
F3 Metal 4in 1 ESC
Combo
£158.85
Holybro Kakute F7 V1.5 Flight Controller Atlalt HV V2 40CH VTX65A BL_32 Tekko 32 F3 Metal 4in 1 ESC Combo Specification: Brand Name: Holybro Item Name: F7 FC65A 4in 1 ESC5.8G 40CH VTX Stack Combo Stack

Height: 26mm Kakute F7 V1.5 Flight Controller (Manual) Brand name: Holybro Item name: Kakute F7 V1.5MCU: STM32F745 32-bit processor IMU: MPU6000 (SPI) Barometer: BMP280 Current Sensor: Approx. 130 amps maximum measurable value USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART)6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work on any UART without uninvert hack. Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only. PPM & PWM receivers are not supported.TF card for Blackbox logging Dimensions: 35x 41x 7mm (
Includes: foam-mounted gyro board in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 8g Tekko 32F3 Metal 4in 1 ESC (Manual) Brand Name: Holybro Model: Tekko 32F3 Metal F3 (M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108 Mhz The 4in 1 has onboard analog current sensor, & TLM function (then no current reading over TLM) Using metal case mosfet for better Heat dissipation Supports Lipo 4-6 S Ext. cap needed for 6s (470uf 35v for 6s usage.)
Size:42 x 42 mm Mounting holes:30.530.5mm Weight: 12g Notice: The air flow is very import if you want to run this 4in 1 in high current. The input cable (from lipo to 4in 1), should be good soldered, & at least 12AWGAtlalt HV V2



...
Available
Holybro Kakute F7 V1.5 Flight Controller & Atlatl HV V2 VTX & 4 PCS 65A BL_32 Tekko32 F3 Metal ESC Combo
Holybro Kakute F7 V1.5
Flight Controller &
Atlatl HV V2 VTX & 4
PCS 65A BL_32 Tekko 32
F3 Metal ESC Combo
£161.80
Holybro Kakute F7 V1.5 Flight Controller Atlatl HV V2 VTX4 PCS 65A BL_32 Tekko 32 F3 Metal ESC Combo Specification: Brand Name: Holybro Tekko 32 F3 Metal ESCModel: Tekko 32 F3 Metal Item Name: 65A BL_32 DShot 1200 ESCQuantity: 4 PCSCon. Current: 65 A Peak Current: 80 A Input Voltage: 3-6S Lipo Support Ext. cap needed for 6s (220uf 35v for 6s usage.)- F3 (M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108 Mhz- Mosfet tested at 4S 65A, under props, nothing covered for 1min- Onboard WS2812B LED
Size: 18 x 27 mm Weight: 4.4g/PCKakute F7 V1.5 AIO (Manual) Item Name: F7 Flight Controller AIO OSD BEC & Current Sensor MCU: STM32F745 32-bit processor IMU: MPU6000 (SPI) Barometer: BMP280 Current Sensor: Approx. 130 amps maximum measurable value USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART)6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work on any UART without uninvert hack. Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only. PPM & PWM receivers are not supported.TF card for Blackbox logging Dimensions: 35x 48x 7mm (
Includes: foam-mounted gyro board in height) Mounting Holes: Standard 30.5mm square to center of holes Weight: 11.2g Atlatl HV V2: Item Name: 5.8G 40CH 25/200/500/800m W FPV Transmitter Model: Atlatl HV V2 Transmitting Output Power: 25m W/ 200m W/ 500m W/ 800m W Switchable Audio: 6 MHz + 6.5 MHz Mono Antenna Connector: MMCXInput Voltage: 7-28V (2-6S Lipo) Dimen

...
Available

Holybro Kakute F7 HDV Flight Controller Tekko32 F3 HDV 40A 3-6S
Blheli_32 4 In 1 Brushless ESC

OverviewHolyBro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect HolyBro Kakute F7 HDV to the DJI FPV VTx, for both signal and power.New BLHELI32 ESC with F3 MCU, give more smooth control and fasterresponding speed. Supports up to 55A burst and 40A continued.Specifications:Kakute F7 HDV Flight ControllerMCU: STM32F745 32-bit processorIMU:PMU6000Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)6 hardware UARTS (UART1, 2, 3, 4, 6, 7)All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without uninvert hack.Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are
not supported.TF card for Blackbox loggingDimensions: 35x35mmMounting Holes: Standard 30.5mm square to center of holesWeight: 8gTekko32 F3 HDV 40A ESC32bit ESC with BLHELI32 firmwareSupports 3-6S lipo inputPWM input, TLM supportedVoltage output (VBAT)NO BECSupports oneshot / Multishot / Dshot PWMMounting holes 30.5x30.5mmSupports damped lightF3 MCU, runs double faster than F051Extra Cap needed for high current or 6s usageDimensions: 44x37x6mmWeight: 11.6gFeatures:Supports Betaflight, Butterflight, and Cleanflight. High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units
Buy
Availability: In Stock
£101.54
toys & games
Description Reviews / Comments Add New

Product Description

Overview Holy Bro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holy Bro Kakute F7 HDV to the DJI FPV VTx, for both signal & power. New BLHELI32 ESC with F3 MCU, give more smooth control & fasterresponding speed. Supports up to 55A burst & 40A continued. Specifications: Kakute F7 HDV Flight Controller MCU: STM32F745 32-bit processor IMU:PMU6000 Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB (Universal Serial Bus) does not take up a UART)6 hardware UARTS (UART1, 2, 3, 4, 6, 7) All UARTS support hardware inversion. SBUS, Smart Port, & other inverted protocols work on any UART without uninvert hack. Supports serial receivers (SBUS, i Bus, Spektrum, Crossfire) only. PPM & PWM receivers are not supported.TF card for Blackbox logging Dimensions: 35x 35mm Mounting Holes: Standard 30.5mm square to center of holes Weight: 8g Tekko 32 F3 HDV 40A ESC32bit ESC with BLHELI32 firmware Supports 3-6S lipo input PWM input, TLM supported Voltage output (VBAT)NO BECSupports oneshot / Multishot / Dshot PWMMounting holes 30.5x 30.5mm Supports damped light F3 MCU, runs double faster than F051 Extra Cap needed for high current or 6s usage Dimensions: 44x 37x 6mm Weight: 11.6g
Features: Supports Betaflight, Butterflight, & Cleanflight. High-performance / low-noise IMU. MPU6000 with 6-axis gyro & accelerometer. Ready for autonomous flight: Integrated BMP280 barometer & SCL/SDA for use with external GPS/magnetometer units

Reviews/Comments

Add New

Intelligent Comparison

Oooops!
We couldn't find anything!
Perhaps this product's unique.... Or perhaps we are still looking for comparisons!
Click to bump this page and we'll hurry up.

Price History

Vouchers

No voucher codes found.
Do you know a voucher code for this product or supplier? Add it to Insights for others to use.

Facebook

Jargon Buster

USB - Universal Serial Bus
GPS - Global Positioning System - Global position using satellites
Flight - The process of of an object moving through the air
speed - A measurement of how fast an object travels between two points
USB - Universal Serial Bus. A method of connecting a device to a computer
Performance - When someone is presenting a form of entertainment, also how well someone is doing within a role.
Convenient - Something that suits and fits well to other activities.

Supplier Information

Banggood US
Banggood is your one-stop online shop for a wide range of products at unbeatable prices. From electronics and gadgets to fashion, home goods, and outdoor gear, we've got something for everyone. With thousands of products from top brands and emerging designers, you'll find the latest trends and must-have items right at your fingertips. Plus, our user-friendly website and mobile app make shopping a breeze, with secure payment options and fast, reliable shipping worldwide. Whether you're looking for the hottest tech gadgets, stylish clothing, or practical everyday essentials, Banggood has you covered. Shop now and discover why millions of customers trust us for their shopping needs!
Page Updated: 2025-01-23 13:29:24

Community Generated Product Tags

Oh No! The productWIKI community hasn't generated any tags for this product yet!
Menu