Feature 1.STEM LEARNING KIT
- Perfect choice for beginners to learn robotics, electronics & program.2.8-IN-1 FUNCTIONS
- With

...

Feature:1. This is a complete learning kit based on Raspberry Pi with Android App. For better learning, an elaborately-written user manual, code with explanation & thorough schematic diagrams are provided.2. The Raspberry Pi board is used as control. The kit uses a step-down DC-DC converter module to reduce input voltage & a motor driver module with L298N. Also a webcam is included with a USB (Universal Serial Bus) Wi-Fi adapter so you can check the video in a real-time manner on your PC or cell phone.3. On the PC, you can control the car move forward/backward & turn left/right, as well as control the camera to turn vertically & horizontally so as to capture the image in different directions.4. A great kit for you to start studying Raspberry Pi (both code & application), learn about the basic components & modules in electronics, & then use the knowledge learnt to explore greater fields!5. Working Voltage: 7V-12V; Powered by two 18650 rechargeable lithium batteries. Package Included:1 pack x Acrylic plates 1 pack x Threaded fasteners 1 x Tower Pro Micro Servo SG902 x Gear Reducer 2 x Driven wheel 2 x Active wheel 1 x 16-Channel 12-bit PWM driver 1 x L298N DC Motor Driver Module 1 x Step-down DC-DC Converter Module 1 x USB (Universal Serial Bus) Wi-Fi Adapter 1 x USB (Universal Serial Bus) Camera 1 x Dual 18650 battery holder 1 x Ribbon 1 x USB (Universal Serial Bus) Cable Serval Dupont Wires 1 x Screwdriver 1 x Cross Socket Wrench ...

The kit uses the Sun Founder Nano board as control. A Sun Founder Servo Control Board integrates battery, servo, Nano board, & n RF24l 01 wireless module together. This kit is equipped with a Sun Founder Mobile Robot Remote Controller so that you can observe & control the robot remotely.
Features:1. This is the Crawling Quadruped Robot kit for. It

Includes:: everything you need to build a cool crawling quadruped robot with wireless remote control.2. Powered by two 18650 rechargeable lithium batteries, its a four-leg mobile robot & each leg has three joints driven by servos.3. This kit is also equipped with a remote controller so that you can observe & control the robot remotely.4. With the sample sketches provided, you can make the robot move forward, backward, left, & right or dance by remote control.5. You can also make your own sketch to realize different movements. Package Included:1 pack x Acrylic Plates 1 x Calibration Chart 1 pack x Threaded Fasteners 2 x n RF24l 01 Module 2 x Sun Founder Nano Board 1 x Sun Founder Mobile Robot Remote Controller 1 x Sun Founder Servo Control Board 2 x dual 18650 Battery Holder 12 x EMAX ES08AⅡ Analog Servo 1 x USB (Universal Serial Bus) Data Cable 1 x Wire Harness Tube (80cm)1 x Ribbon (50cm)1 x Screwdriver


...

Sunglasses Case Clip on Glasses Box Protector Goggle Case
Features: Molded hard case will fit most clip-on sunglasses.
...

Sunhans 3000m W 35d Bm 2.4 G Hz 11b/g/n Wireless Wi Fi Signal Booster Signal Amplifier This indoor signal booster can increase the effective range & coverage area of your Wi-Fi network., It is Ideal for increase the 2000-2500 Mhz frequency devices. Description: Model: SH24BTA-NP/N: 24BTAN24014 Barcode: 6958917600827 Operating range: 2400~2500 M Hz Channel

Width: 20 Mhz 40 Mhz Supported standards: IEEE 802.11b/g/n Operation mode: Bi-directional, half-duplex, time division duplex Connector type: To radio SMA female (hole inside). To antenna RP-SMA male (pin inside) Output power: 3000m W (35d Bm) Input power: 0 ~ 20d Bm Transmit gain: 15
- 18d B Receiver gain: is less than or equal to 12d B Noise figure: = 3.5d B typical Frequency response: + 1d B over operating range Power adapter: 12V/2A DC, 100~240 V Operating temperature: -20 C to +70 degrees C degrees Operating humidity: Up to 75% relative humidity
Material: Cast aluminum LED light: Power status LED & activity status LEDBooster weight: 150g Booster

Size: 8.4 x 4.7 x 1.7cm Package weight: 450g Package

Size: 21.3 x 13.5 x 5cm Use Step 01: Remove the Antenna from the Wireless Router (Access Point). Step 02: Use this cable (RG316) to connect Amplifier input port with router output port: note that cable is in standard spec. Step 03: Connect the antenna with output port of Amplifier. Step 04: Power the amplifier with the matching source adapter: DC 12V. Attention: The power amplifier is not suitable for use in high power devices Package Included:1 x SH24BTA-N Wifi Signal Bo







...

SUNKKO 18650 Battery Fixture 4-cell 6-cell 8-cell options Lightweight Reliable Designed for High-Quality Welding Workflow Enhancement ...

Only US$5.02, buy best sunkko 18650 battery fixture single row fixed double sided spot welding lithium battery pack weld fixture batteries fixed holder sale online store at wholesale price. ...

SUNKKO 738AL Spot Welding Machine New Upgraded Telescopic Arm Handheld Spot Welder 18650 Battery Weld Precision Pulse Spot Welder ...

SUNKKO 950T-Pro High Power 75W Soldering Station with Electric Soldering Iron Anti-static Fast Heat-Up to 480°C LED Display T12-B2 Soldering Core Precise Temperature Control for Quality-Assured Soldering ...

SUNKKO BAL-5624 Energy Transfer Equalizer Balancer for Li-ion lifepo 4 Batteries 2S~24S 5A High Balance Current Exceptional Voltage Balancing Compact Design Quick Charging Prolong Battery Life ...