Specification:  Brand Name: CUAV  Model: Item Name:C-RTK Expansion Module - Integrated with Buzzer Safety Switch LED Light  Dimension: 21x 12x 35mm (Lx Wx H)   Weight: 11g   Package Included: 1x Expansion Module 1x Connection Cable 1x USB (Universal Serial Bus) Cable ...

Specification:  Brand Name: CUAV  Item Name:CUAV CAN 180A 88W UBEC PDB Integrated with Flight Controller Bottom Board MCU: STM32F412 100 Mhz 512K Flash 256K RAM - Support 15-62V Wide Voltage Input (4-15S Lipo)-   Ouput Con. Current: 180A -Accurate Current Measurement: 0-110A - 88W UBEC Double stable voltage output - 5V Output, Con. Current: 6A; Max. Current: 8A - 12V Output, Con. Current: 3.5A; Max. Current: 4A  Support APMPX4 firmware   Working Temperature: -20--100℃  Dimension: 12x 10x 1.2cm (Lx Wx H)   Weight: 214g  Package Included: 1x CUAV CAN PDB Board 1x 30cm Power Cable (Black) 1x 30cm Power Cable (Red) ...

CAN PMUis a high-precision power module developed by CUAV. It uses the UAVCANprotocol & runs the CUAV ITT compensation algorithm, which enables drones to get the battery data more accurately. Overview:CAN PMU is a UAV power management unit module with built-in STM32F4processor & running CUAV ITT algorithm. It can accurately measure UAVvoltage & current in real time. It can support 6-62V voltage & 110A currentat maximum, & can output 5.4V 8A. The flight controller is powered by CANbus communication & supports the standard UAV CAN protocol. Each PMUunit is factory calibrated to ensure good consistency & high accuracy Specifications Processor:STM32F412 Voltage input: 6~62V (2-15S) Max current:110 A Voltage accuracy:0.05 V Current accuracy:0.1 A Resolution:0.01A/VMax output power:6000W/90 S Max stable power:5000 W Power port output:5.4V/5 A Protocol:UAVCANOperating temp:-20~+100 Firmware upgrade: Supported. Calibration: Not needed. Interface Type:IN/OUT:XT90 (Cable)/ Amass 8.0 (Module) Power port:5025850670CAN:GHR-04V-SAppearance:
Size:46.5mm * 38.5mm * 22.5mm Weight:76g Notes:- Please read the product manual carefully.- Please check the connection carefully before connecting the battery- Please use at rated voltage, current & power- Please read the documentation center for configuration & use- Do not disassemble Firmware upgrade: Click for a firmware upgrade tutorial. Manual: Click For Manual.
...

CUAV HV_PM 10-60V Pixhack Pixhawk Power Module XT60 Plug for RC Drone FPV Racing Specification: Brand name: CUAVItem name: HV_PM power module Input voltage: 10-60V (3s~14s battery) Voltage detection accuracy: +
- 0.1v Current detection accuracy: +
- 0.2a A Support higher power port output current: 5 A Maximum (detection) current: 60 A Feature: Provide 5V voltage output & maximum 5A current to fly control power supply Detection of the current voltage output analog signal to the flight control Detection of the current system output analog signal to the flight control Package included:1 x HV_PM power module

...

CUAV IST8 External Compass Module Sensor I2C 8310 for PX4 / CUAV V5 Flight Controller GPSThe IST8 compass module is built into i Senteks 33mm LGA geomagnetic sensor IST8310, which is widely used in drone products. The PX4 & Ardu Pilot have been applied to the Pix flight control & can be used as an external compass for the V5 flight control. Specification: Compass: IST8310 Power input: 5v Interface: I2 C Working temperature: -40~85c
Size: 23*14*9mm Weight: 5g More Deatails Data, Click here Download Package Included:1 x IST8310 Compass Module
...

CUAV Pixhack V5 Autopilot STM32F765 2MB Flash Flight Controller for RC Drone Specification: Brand name:CUAVItem name: Pixhack V5 Autopilot Flight Controller Weight: 90g Dimensions: 44x 84x 12mm Operating temperature: -20 ~ 80 C Main FMU Processor: STM32F76532 Bit Arm Cortex-M7, 216 M Hz, 2MB memory, 512KB RAMIO Processor: STM32F10032 Bit Arm Cortex-M3, 24 M Hz, 8KB SRAMOn-board sensors: Accelerometer/ Gyroscope: ICM-20689 Accelerometer/ Gyroscope: BMI055 Magnetometer: IST8310 Barometer: MS5611 Interfaces:8-14 PWM outputs (6 from IO, 8 from FMU)3 dedicated PWM/ Capture inputs on FMUDedicated R/C input for CPPMDedicated R/C input for ppm/DSM & S. Busanalog / PWM RSSI input S. Bus servo output 5 general purpose serial ports 4 I2C ports 4 SPI buses 2 CANBuses with serial ESCAnalog inputs for voltage / current of 2 batteries Power System: Power: 4.3~5.4VUSB Input: 4.75~5.25 V Servo Rail Input: 0~36 V Package Included:1 x Pixhack V5 Autopilot Flight Controller ...

Description: Screen resolution: 128*64 Screen

Material: OLEDScreen
Colour: Yellow & blue Data interface:


...

Description:115m A / 5 V Specifications Does fit the Matrix Vision Bluefox MV mounting holes (camera center off-centered) Package Included :1 x PX4FLOW 2.1 Smart Optic Flow Module ...

Specifications: Hardware Parameters:- Main FMU Processor: STM32F765 (32-bit, 216 M Hz, 2MB flash, 512KB RAM)

Features:-

...

V5 + Auto Pilot V5+ Auto Pilotis an advanced autopilot designed & made in CUAV. The board is based on the FMUv 5open hardware design, the external interface uses the Dronecode standard pinouts, & the modular design allows the user to design its backplane. It is fully compatible with PX4and Ardu Pilotfirmware. Mainly used for academic & business development. Description: Main FMUProcessor:STM32F76532 Bit Arm Cortex-M7, 216 M Hz, 2 M Bmemory, 512KBRAMIOProcessor:STM32F10032 Bit Arm Cortex-M3, 24 M Hz, 8KBSRAMOn-boardsensors: Accelerometer/ Gyroscope:ICM-20689 Accelerometer/ Gyroscope:BMI055 Magnetometer:IST8310 Barometer:MS5611 Interfaces:8-14PWMoutputs (6from IO, 8from FMU)3dedicated PWM/ Captureinputson FMUDedicated R/ Cinputfor CPPMDedicated R/ Cinputfor PPMand S. Busanalog/PWMRSSIinput S. Busservooutput 5generalpurposeserialports 4I2 Cports 4SPIbuses 2CANBuseswithserial ESCAnaloginputsforvoltage/currentof 2batteries Power System: Power:4.3~5.4VUSBInput:4.75~5.25 V Servo Rail Input:0~36 V Weightand Dimensions: Weight:90g Dimensions:85.5*42*33mm Other Characteristics: Operatingtemperature:-20~80c (Measuredvalue) Package Included:1 XCUAV V5+ Pixhawk ...