null Description: This RC receiver unit is Fr Sky D8 compatible. It offers full 7-channel support in ultra-light weight & mini size. It is suitable for 1/87 RC conversion.
Features:1. Fr Sky 2.4 G Hz D8 compatible 2. 7 channel support 3. Integrated two standalone Bi-directional ESC (maximum 1A currency)4. Integrated one Single-directional ESC (maximum 3A currency)4. Mini size (16.0 x 10.0 x 2.5mm)5. Operating Voltage 3.0V – 4.2V6. Product Weight: 0.5g Output Usage: Servo signal output:CH1: (Spare, normally use to control the sound unit or light unit)CH2: (Throttle)CH3: (Spare, normally use to control the sound unit or light unit)CH6: (Spare)CH7: (Spare) Bi-directional ESC output:OUT1/OUT2: connect a brushed motor, tank mode mixed controlled by CH2/CH4 signal from transmitter OUT3/OUT4: connect a brushed motor, tank mode mixed controlled by CH2/CH4 signal from transmitter CH2 is throttle & CH4 is steering Single-directional ESC or LED output:OUT5: connect a brushed motor or LEDs, controlled by CH5 signal from transmitter Compatible Transmitters: Fr Sky Stick-type transmitter Jumper Stick-type transmitter like T8SG/T12/T12PRO/T16/T16PROAny OPENTX & Deviation Stick-type transmitter installed with CC2500 RF module Package Included:1 x Receiver Bind: Power on the receiver, LED will flash slowly. Wait 15 seconds & the LED will flash quickly, this means the receiver is in paring mode. Now you could operate your transmitter to start the bind operation. Once the bind is successful, the LED on recei
...

null Description: This RC receiver unit is Fr Sky D8 compatible. It offers full 7-channel support in ultra-light weight & mini size. It is suitable for 1/87 RC conversion.
Features:1. Fr Sky 2.4 G Hz D8 compatible 2. 7 channel support 3. Integrated two standalone Bi-directional ESC (max 1A currency)4. Integrated one Single-directional ESC (max 3A currency)4. Mini size (16.0 x 10.0 x 2.5mm)5. Operating Voltage 3.0V – 4.2V6. Product Weight: 0.5g Output Usage: Servo signal output:CH1: (Steering)CH2: (Throttle)CH3: (Spare, normally use to control the sound unit or light unit)CH4: (Spare, normally use to control the sound unit or light unit)CH7: (Spare) Bi-directional ESC output:OUT1/OUT2: connect a brushed motor, controlled by CH2 signal from transmitter OUT3/OUT4: connect a brushed motor, controlled by CH6 signal from transmitter Single-directional ESC or LED output:OUT5: connect a brushed motor or LEDs, controlled by CH5 signal from transmitter Compatible Transmitters: Fr Sky Stick-type transmitter Jumper Stick-type transmitter like T8SG/T12/T12PRO/T16/T16PROAny OPENTX & Deviation Stick-type transmitter installed with CC2500 RF module Package Included:1 x Receiver Bind: Power on the receiver, LED will flash slowly. Wait 15 seconds & the LED will flash quickly, this means the receiver is in paring mode. Now you could operate your transmitter to start the bind operation. Once the bind is successful, the LED on receiver will be on. Power off both your transmitter & receiver then power them on
...

Description: Das 87 DSM2 7CH PPM Transmitter is an AR6100 type receiver reprogrammed to be a DSM2 compatible short range transmitter. It is intended to be used as a 7ch TX module with an older transmitter or any DIY RC project with PPM signal out. The TX accept idle high & low (normal & inverted PPM).
Features: Das 87 DSM2 7CH PPM Transmitter is a DSM2-compatible transmitter module intended to convert traditional joystick transmitters to 2.4 G Hz. It is a DIY solution requiring some understanding of electronics & soldering. It may require a voltage regulator & Zener diode to control voltages from the host transmitter. The host transmitter can have 2 to 12 channels. The first 7 PPM pulses will be transmitted. To use as a module you will need a 3.3 or 5v regulator if it is to be powered from 2S or 3S Lipo. Some PPM signals exceed 3.6v so you may need a 3.3v Zener diode & 1000 ohm resistor to limit the voltage. Specification The TX moudle can be powered by 3.2-10v The PPM input to the signal Pin 7 must be 2.1v to 3.6v (max) when high The PPM input must be below 0.8v when low Pin 7 floats needs active (strong) highs & lows The PPM signal can idle high or low User manual, please click here Bind:1. Switch the Rx on in bind mode.2. Put bind plug on Tx 1 Pin 1.3. Switch Tx 1 on.4. Wait for Tx & Rx led to stop flashing. Package Included:1 x DSM2 7CH PPM Transmitter 1X Bind Cable
...

null Description: Item Name: Das 87 Flysky AFHDS2A 7CH Nano Receiver
Material: Metal
Colour: As the picture

...

Description: Das Mikro DS87E02-4 drive unimog DIYKit rc car vehicle models without electric parts. Suitablefor URUAV 1/24 4WD 2.4G mini crawler model vehicle parts Note: This product included small parts & pay attention to not to swallow it. All the products should be used by the aged above 6 years old. Package included:1X DS87E02-4 rc car kit ...

Das Mikro DSM2 DSMX 7CH 2.4 Ghz RC Micro Receiver With PPM Output Description: Brand: Das Mikro Item:7CH 2.4 Ghz RC Micro Receiver Channels: 7channels (7channels PPM)1.8A Bi-Directional Brushed Motor Driver controlled by throttle channel Receiving Sensitivity: -99d Bm Frequency Range: 2.4-2.48 G Hz Power: 3.7-5V DCWeight: 0.82g Antenna Length: 30mm
Size: 21mm*13mm*2.5mm
Colour: Blue Signal Output:CH1-CH7 output normal PWM signal When TEST is connected to GND, CH1 output 7 channel PPM signal 1.8A Bi-Directional Brushed Motor Driver controlled by throttle channel (Channel 1) Bind: Make sure the transmitter is power off. Power on DSM2/DSMX receiver. Long press the pair button. After around 2 seconds the led changed to fast flashing, now the receiver is in pairing mode. Then turn on the transmitter & make the transmitter to pairing mode. Wait the receiver led from fast flashing to turn off, now the pairing is done. Power off the transmitter & receiver then power on again then the receiver will work. Failsafe: Turn on the transmitter & the receiver & make sure receiver is working normally. Adjust each channel to the exact position you want to have in failsafe mode. Make sure the transmitter is not in pair mode. Long press the pair button & wait the led to be fast flashing, & now the failsafe data is saved. Power off the receiver & power on again the failsafe will work. Das Mikro 7CH Micro Receiver Manual, please clik here Package Included:1 XDas Mikro 7CH 2.4 Ghz RC Micro Receiver

...

Description: Item Name:DSMX/DSM26CHNano RCReceiver Channels:6channels Power:3-10VDCAntenna Length:30mm Product
Size:9.9mm*9.2mm*2.5mm
...

Description: This RC receiver unit is Futaba S-FHSScompatible. It offers full 4-channel support in ultra-light weight & micro size. It is ideal for micro racing cars.
Features:1. Futaba 2.4 G Hz S-FHSS compatible 2. High performance CPU enhance precision control feeling 3. 4 channel support 4. Micro size (23x 15.5x 7mm)5. Ideal for any micro rc racing chassis 6. Added failsafe function 7. Operating Voltage 4.8V
- 7.4V:8. Weight: 2.7g Compatible Transmitters: Futaba 7PX, 4PX, 4PV, 3PV...... Package Included:1 x Receiver 4 x 1.5mm 3P JST plug with cable Bind & Failsafe: Power on your transmitter & receiver. Adjust transmitter each channel to the exact position you want to have in failsafe mode. Transmitter set to pair mode. Receiver led should be on. Long press the pair button. After around 2 seconds the LED will turn to fast flashing first then turn to on status again. Now the pairing is done & the failsafe data is saved. Power off the transmitter & receiver then power on again then the receiver will work.

...

Specification: Item Das Mikro Sanwa Receiver Material Electronic component Color As the picture Weight 2.7g Description: This RC receiver unit is Sanwa FHSS-4 & FHSS-3 compatible. It offers full 4-channel support in ultra- light weight & micro size. It is ideal for micro racing cars.
Features:1. Das Mikro Sanwa 2.4 G Hz FH3/FH4 Selectable Via Transmitter 2. High performance CPU enhance precision control feeling 3. 4 channel support 4. Micro size (25.5x 18.5x 8.7mm)5. Ideal for any micro rc racing chassis 6. Added failsafe function 7. Operating Voltage 4.8V
- 7.4V:8. Weight: 2.7g 9. Battery Voltage Fail-Safe Limit: 3.5-5.0V (FH3) / 3.5-7.4V (FH4) Compatible Transmitters: Sanwa MT4 Sanwa MT4 S Sanwa M11 X Sanwa M12 Sanwa M12 S Sanwa EXZES ZZSanwa EXZES ZSanwa EXZES XSanwa MT-SSanwa MX-3 X Sanwa GEMINI X. Package included:1 x Receiver 4 x 1.5mm 3P JST Plug with Cable

...

Gyro Unit Set For Kyosho Mini-Z RC Car Parts Description: Weight: 1g Wire Length: 80mm This Gyro Unit plugs right into the main board of your MR-03 & will help you keep your MR-03 under control. The Gyro Unit will automatic correct of steering & throttle. Basically it will keep the steering aimed to the global direction, so say your rear tires loose traction & the chassis come to an angle, this will counter steer for you faster than humanely possible. Very cool, & really impressive having the car stable like if it was following a rail on low traction surfaces (wood, tiles). Package Included:1 XGyro Unit Set ...