Description: Das 87 DSM2 7CH PPM Transmitter is an AR6100 type receiver reprogrammed to be a DSM2 compatible short range transmitter. It is intended to be used as a 7ch TX module with an older transmitter or any DIY RC project with PPM signal out. The TX accept idle high & low (normal & inverted PPM).
Features: Das 87 DSM2 7CH PPM Transmitter is a DSM2-compatible transmitter module intended to convert traditional joystick transmitters to 2.4 G Hz. It is a DIY solution requiring some understanding of electronics & soldering. It may require a voltage regulator & Zener diode to control voltages from the host transmitter. The host transmitter can have 2 to 12 channels. The first 7 PPM pulses will be transmitted. To use as a module you will need a 3.3 or 5v regulator if it is to be powered from 2S or 3S Lipo. Some PPM signals exceed 3.6v so you may need a 3.3v Zener diode & 1000 ohm resistor to limit the voltage. Specification The TX moudle can be powered by 3.2-10v The PPM input to the signal Pin 7 must be 2.1v to 3.6v (max) when high The PPM input must be below 0.8v when low Pin 7 floats needs active (strong) highs & lows The PPM signal can idle high or low User manual, please click here Bind:1. Switch the Rx on in bind mode.2. Put bind plug on Tx 1 Pin 1.3. Switch Tx 1 on.4. Wait for Tx & Rx led to stop flashing. Package Included:1 x DSM2 7CH PPM Transmitter 1X Bind Cable
...

null Description: Item Name: Das 87 Flysky AFHDS2A 7CH Nano Receiver
Material: Metal
Colour: As the picture

...

Description: Das Mikro DS87E02-4 drive unimog DIYKit rc car vehicle models without electric parts. Suitablefor URUAV 1/24 4WD 2.4G mini crawler model vehicle parts Note: This product included small parts & pay attention to not to swallow it. All the products should be used by the aged above 6 years old. Package included:1X DS87E02-4 rc car kit ...

Description: Das Mikro DS87E07 734 metal rc car bulldozer without power motor diy kit vehicle models. Suitablefor URUAV 1/24 4WD 2.4G mini crawler model vehicle parts Note: This product included small parts & pay attention to not to swallow it. All the products should be used by the aged above 6 years old. Note:1. This kit is very small, only suitable for senior player.2. See more intall details in the facebook, search the titile is ok. Package included:1x DS87E07 rc car kit ...

Das Mikro DSM2 DSMX 7CH 2.4 Ghz RC Micro Receiver With PPM Output Description: Brand: Das Mikro Item:7CH 2.4 Ghz RC Micro Receiver Channels: 7channels (7channels PPM)1.8A Bi-Directional Brushed Motor Driver controlled by throttle channel Receiving Sensitivity: -99d Bm Frequency Range: 2.4-2.48 G Hz Power: 3.7-5V DCWeight: 0.82g Antenna Length: 30mm
Size: 21mm*13mm*2.5mm
Colour: Blue Signal Output:CH1-CH7 output normal PWM signal When TEST is connected to GND, CH1 output 7 channel PPM signal 1.8A Bi-Directional Brushed Motor Driver controlled by throttle channel (Channel 1) Bind: Make sure the transmitter is power off. Power on DSM2/DSMX receiver. Long press the pair button. After around 2 seconds the led changed to fast flashing, now the receiver is in pairing mode. Then turn on the transmitter & make the transmitter to pairing mode. Wait the receiver led from fast flashing to turn off, now the pairing is done. Power off the transmitter & receiver then power on again then the receiver will work. Failsafe: Turn on the transmitter & the receiver & make sure receiver is working normally. Adjust each channel to the exact position you want to have in failsafe mode. Make sure the transmitter is not in pair mode. Long press the pair button & wait the led to be fast flashing, & now the failsafe data is saved. Power off the receiver & power on again the failsafe will work. Das Mikro 7CH Micro Receiver Manual, please clik here Package Included:1 XDas Mikro 7CH 2.4 Ghz RC Micro Receiver

...

Description: This RC receiver unit is Futaba S-FHSScompatible. It offers full 4-channel support in ultra-light weight & micro size. It is ideal for micro racing cars.
Features:1. Futaba 2.4 G Hz S-FHSS compatible 2. High performance CPU enhance precision control feeling 3. 4 channel support 4. Micro size (23x 15.5x 7mm)5. Ideal for any micro rc racing chassis 6. Added failsafe function 7. Operating Voltage 4.8V
- 7.4V:8. Weight: 2.7g Compatible Transmitters: Futaba 7PX, 4PX, 4PV, 3PV...... Package Included:1 x Receiver 4 x 1.5mm 3P JST plug with cable Bind & Failsafe: Power on your transmitter & receiver. Adjust transmitter each channel to the exact position you want to have in failsafe mode. Transmitter set to pair mode. Receiver led should be on. Long press the pair button. After around 2 seconds the LED will turn to fast flashing first then turn to on status again. Now the pairing is done & the failsafe data is saved. Power off the transmitter & receiver then power on again then the receiver will work.

...

Specification: Item Das Mikro Sanwa Receiver Material Electronic component Color As the picture Weight 2.7g Description: This RC receiver unit is Sanwa FHSS-4 & FHSS-3 compatible. It offers full 4-channel support in ultra- light weight & micro size. It is ideal for micro racing cars.
Features:1. Das Mikro Sanwa 2.4 G Hz FH3/FH4 Selectable Via Transmitter 2. High performance CPU enhance precision control feeling 3. 4 channel support 4. Micro size (25.5x 18.5x 8.7mm)5. Ideal for any micro rc racing chassis 6. Added failsafe function 7. Operating Voltage 4.8V
- 7.4V:8. Weight: 2.7g 9. Battery Voltage Fail-Safe Limit: 3.5-5.0V (FH3) / 3.5-7.4V (FH4) Compatible Transmitters: Sanwa MT4 Sanwa MT4 S Sanwa M11 X Sanwa M12 Sanwa M12 S Sanwa EXZES ZZSanwa EXZES ZSanwa EXZES XSanwa MT-SSanwa MX-3 X Sanwa GEMINI X. Package included:1 x Receiver 4 x 1.5mm 3P JST Plug with Cable

...

Gyro Unit Set For Kyosho Mini-Z RC Car Parts Description: Weight: 1g Wire Length: 80mm This Gyro Unit plugs right into the main board of your MR-03 & will help you keep your MR-03 under control. The Gyro Unit will automatic correct of steering & throttle. Basically it will keep the steering aimed to the global direction, so say your rear tires loose traction & the chassis come to an angle, this will counter steer for you faster than humanely possible. Very cool, & really impressive having the car stable like if it was following a rail on low traction surfaces (wood, tiles). Package Included:1 XGyro Unit Set ...

Description: Weight: 1g Wire Length: 60mm This Gyro Unit plugs right into the main board of your MINI-Z AWD Sports MA-020S/ Overland sports/ Mini-Z Racer sports 2 MR-03and will help you keep your vehicle under control. The Gyro Unit will automatic correct of steering & throttle. Basically it will keep the steering aimed to the global direction, so say your rear tires loose traction & the chassis come to an angle, this will counter steer for you faster than humanely possible. Very cool, & really impressive having the car stable like if it was following a rail on low traction surfaces (wood, tiles). Package Included:1 x Gyro Unit Set ...

Description: The USB (Universal Serial Bus) Adapter HS lets you connect a PC or Android phone (need OTG to USB (Universal Serial Bus) converter) to the I.C.S. plug on your MINI-Z, & means that you can adjust various setting parameters. It supports the latest EVO chassis (only PC software available) & all previous Mini-z chassis (both PC software & Android app available). It also could be used to upgrade transmitters like EX-6, EX-6R, EX-1, EX-2, EX-RR. For KO PROPO transmitter/ESC/SERVO settings, you could download software from:http://kopropo.com/america/support/ics-interactive-communication-system/ For Kyosho transmitter & Mini-z, , you could download software fromhttp://kyosho.com/mini-z-info/support/settings-&-firmwaresoftware/ Package Included:1 x Das Mikro I.C.S. USB (Universal Serial Bus) Adaptor HS1 x 3P servo cable (for transmitter upgrade)1 x 3P to 4P cable (for Mini-z ICS settings) ...