Real Test of output voltage Input voltage output Electric current Effectiveness Curve Description: Input voltage range: 3~4.2V DCOutput: 5V 2 A Standby current: 5m A Pins distance: 2.54mm Size Weight: 27x 15x 3mm, 2g

Features:-VB2A5 is a compact, high-efficiency, synchronous step-up converter for asingle-cell Li-ion/polymer battery. It can boost the voltage to 5V, allowing youto run a receiver on a single cell lipo.-Use for 1cell Li-ion or Li Po.-Synchronous step-up converter.-Guaranteed 2A Output Current at VOUT = 5V from 3.3V Input-Reverse input polarity protection.-Over-temperature protection. Package Include:1x Voltage Booster

...

Matek Systems F405-STD Beta Flight STM32F405 Flight Controller Built-in Inverter for SBUS Input Specification (user manual): Brand: Matek Systems Item name: Flight Control Board
Size: 36x 36mm Mounting hole: 30.5mm Weight: 7g MCU: 168 M Hz STM32F405RGT6IMU: 32K ICM20602 gyro/accelerometer (SPI) Baro: BMP280 (I2C)OSD: Beta Flight OSD w/ AT7456E chip Blackbox: Micro SD card slot (SD/SDHC)VCP, UART1, UART2, UART3, UART4, UART5 Built in inverter for SBUS input (UART2-RX)PPM/UART Shared: UART2-RXSoft Serial on TX2, S5 or S6 optional Camera control on S6 or DAC optional Smartaudio Tramp VTX protocol supported Battery Voltage Sensor: 1:10 Current Sensor: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)BEC 5V: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)LDO 3.3V: Max.300m AI2C1 SDASCL: Yes WS2812 Led Strip: Yes Beeper: Yes RSSI: Yes
Features:3x LEDs for FC STATUS (Blue, Red) & 3.3V indicator (Red)6x PWM / DShot outputs without conflict 2x 2812LED outputs option 5x UARTs 1x Group of 5V/G/S1/S2/S3/S4 pads for 4in 1 ESC Signal/GND4x pairs of corner pads for ESC Signal/GND connections (DSHOT compatible)1x pair I2C1 pads 1x Side-press button for BOOT (DFU) mode 1x 16pin bottom mounted FFC Slot for FCHUB-6S, FCHUB-VTX or FCHUB-W connection Package included:1x flight control board 2x 0.5mm*16 Pin 5cm Flexible Flat Cable 4x M3 Anti-vibration Standoffs

...

Matek F405-STDBeta Flight STM32F405 Flight Controller + Matek FCHUB-6S Hub Power Distribution Board Specification: Matek F405-STD (user manual): Brand: Matek Systems Item name: Flight Control Board
Size: 36x 36mm Mounting hole: 30.5mm Weight: 7g MCU: 168 M Hz STM32F405RGT6IMU: 32K ICM20602 gyro/accelerometer (SPI) Baro: BMP280 (I2C)OSD: Beta Flight OSD w/ AT7456E chip Blackbox: Micro SD card slot (SD/SDHC)VCP, UART1, UART2, UART3, UART4, UART5 Built in inverter for SBUS input (UART2-RX)PPM/UART Shared: UART2-RXSoft Serial on TX2, S5 or S6 optional Camera control on S6 or DAC optional Smartaudio Tramp VTX protocol supported Battery Voltage Sensor: 1:10 Current Sensor: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)BEC 5V: No (FCHUB-6S, FCHUB-VTX, FCHUB-W option)LDO 3.3V: Max.300m AI2C1 SDASCL: Yes WS2812 Led Strip: Yes Beeper: Yes RSSI: Yes Matek FCHUB-6S (user manual): Brand Name: Matek Model:FCHUB-6 S Item Name: Power Distribution Board Built-in Current Sensor
Size: 36x 36mm 30.5x 30.5mm Hole Mounting, M3 Weight: 8.5g BEC Output: 5V10V5V BEC Output:- Designed for RC Receivers, Flight Controllers, OSD & Servos.- DC/DC synchrous buck regulator- Voltage: 5.0V (4.9-5.1)DC
- Current: 1.5A (Max. 2.0A 10S/minute)- Short-circuit tolerant (2 Seconds/minuate)10V BEC Output:-Designed for VTX or FPV Camera- Voltage: 10.0V (9.8-10.2) DC
- Current: 1.5A (Max. 2.0A 10S/minute)- Short-circuit tolerant (2 Seconds/minuate)- 10V can be used to power cameras labeled as 12V.- The 3S Lipo input voltage should be 11V plus. Curr



...

Matek FCHUB-6S Hub Power Distribution Board 5V10V BEC Built-in 184A Current Sensor Describtion:-This PDB distribution power from from a 3-6S Lipo pack to 4 ESCs, as well as providing regulatedfiltered DC 5VDC 10V outputs for powering Cameras, RC receivers, Flight Controllers, Video Transmitters, LEDs, etc.- It also has buit-in 184A current sensor & offers a FFC socket to connect the Matek flight controller conviently. Specification: Brand Name: Matek Model:FCHUB-6 S Item Name: Power Distribution Board Built-in Current Sensor
Size: 36x 36mm 30.5x 30.5mm Hole Mounting, M3 Weight: 8.5g BEC Output: 5V10V5V BEC Output:- Designed for RC Receivers, Flight Controllers, OSD & Servos.- DC/DC synchrous buck regulator- Voltage: 5.0V (4.9-5.1)DC
- Current: 1.5A (Max. 2.0A 10S/minute)- Short-circuit tolerant (2 Seconds/minuate)10V BEC Output:-Designed for VTX or FPV Camera- Voltage: 10.0V (9.8-10.2) DC
- Current: 1.5A (Max. 2.0A 10S/minute)- Short-circuit tolerant (2 Seconds/minuate)- 10V can be used to power cameras labeled as 12V.- The 3S Lipo input voltage should be 11V plus. Current Sensor Module
- Max. Range: 184A- 3.3V ADC- Scale the output voltage to milliamps (1/10th m W/A): 179

Features:- Total 4 pairs ESC solder tabs are fix for X Type frame- Max. 27V input w/ TVS protection- Built-in current sensor 184A- PDB: 4*30A (4*46A, 5 seconds), 4 layers*2oz copper PCB-BEC 5V@1.5A (Max. 2A) w/ 100uf panasonic POSCAP filter
- BEC 10V@1.5A (Max. 2A) w/ 47uf TDK MLCC filter- 5V10V out






...

Matek FCHUB-W Fixed Wings PDB 3-6S Built-in 4 BEC & 104A Current Sensor for RC FPV Racing Drone Specification (user manual): Input voltage range: 9~30V (3~6S Li Po) w/TVS protection Current Senor: 104A, 3.3V ADC, Scale 317 Mounting: 30.5 x 30.5mm, Φ3mm Dimensions: 52 x 36 x 6 mm Weight: 13g 2x ESC power pads 4x BEC on board 3x LED indicators for 5V, 10V & Vx Soldering Holes & Pads:+ & –: Bettery & ESC power pads Curr: Current sensor output Vbat: Bettery voltage G: Ground 3V3: LDO 3.3V5V: BEC 5V10V: BEC 10 V Vx: BEC 5V/6V/7.2V ADJFFC connection: Compatible with MATEKSYS FC F405-STD, F722-STD, F405-OSDMT1: Motor 1 of INAV Flying Wing & Airplane MT2: Motor 2 of INAV Flying Wing & Airplane SV3~SV6: Servo 3~6 of INAV Flying Wing & Airplane VTX: Video Transmitter signal TX5 & RX5: UART5 of F405-STD/F722-STD/F405-OSDBEC 5V output: Designed for Flight controller, Receiver, OSD, Camera, Buzzer, 2812 LED_ Strip, GPS module DC/DC synchronous buck regulator Voltage: 5.0 +/- 0.1VDCContinuous current: 2 Amps, Max.3 A Output Ripple: 20m V (VIn=24V, VOut=5V@2A load) Short-circuit tolerant (2 seconds)BEC 10V output: Designed for Video Transmitter, Gimble DC/DC synchronous buck regulator Voltage: 10.0 +/- 0.2VDC (Input voltage >11V) Continuous current: 2 Amps, Max.3 A Output Ripple: 20m V (VIn=24V, VOut=10V@2A load) Short-circuit tolerant (2 seconds)BEC Vx output: Designed for Servos DC/DC synchronous buck regulator Voltage adjustable, 5V Default, 6V or 7.2V via jumper Continuous current: 5 Amps, Max.5.5 A Output Ripple: 50m V (VIn=24V, V ...

Only US$72.99, buy best matek flight controller f 405-vtol barometer osd microsd card blackbox 2-6s lipo ardupilot inav for rc racing drone fixed-wing airplane sale online store at wholesale price. ...

Only US$134.99, buy best matek flight controller h 743-wing v 3 ardupilot inav 3-8s for rc multirotor airplane fixed-wing drones sale online store at wholesale price. ...

Only US$54.99, buy best matek g 474-heli balance flybarless controller 2-6s lipo for rc helicopter sale online store at wholesale price. ...

Only US$99.99, buy best matek h 743-wlite flight controller built-in osd 2-6s ardupilot inav open source for fpv drone rc airplane sale online store at wholesale price. ...

Matek LED Tail light WS2512B with Loud Buzzer Dual Modes for FPV Racer Multicopters It comes as H Type tail light with 8x WS2812B LEDs Loud Buzzer. It provides dual control modes, can be controlled by Flight Controller firmware (Cleanflight, Betaflight, etc.) or Transmiter. Specification: Brand name: Matek Item name: LED Tail light with Buzzer board Dual modes: FC control TX control TX mode: LED 7 colors (White, Red, Green, Blue, Yellow, Magenta, Cyan) LED 5 status (Constant light, Slow blink, Fast blink, Voilent blink) Buzzer: Lost Plane Finder FC mode: support Naze 32, SPRacing F3, etc. with Clean Flight or Betaflight firmware Input voltage range: 4.5~5.2V DCPower of TX mode (5V IN ): 1W/0.2A~2W/0.4A Sizemounting: Pls check the Layout Weight: 5g Package Included:1 X LED Tail light with Buzzer board ...